FANUC R2000iB/165F 6 AXIS CNC W/ R-30iA CONTROL
HOURS SHOWN ON METER 13,121 Robot Motion Speed J1 110 °/s (1.92 rad/s) J2 110 °/s (1.92 rad/s) J3 110 °/s (1.92 rad/s) J4 150 °/s (2.62 rad/s) J5 150 °/s (2.62 rad/s) J6 220 °/s (3.84 rad/s) Robot ...
FANUC R2000iB/165F 6 AXIS CNC ROBOT W/R30iA CONTROL
HOURS SHOWN ON METER 11,430 Robot Motion Speed J1 110 °/s (1.92 rad/s) J2 110 °/s (1.92 rad/s) J3 110 °/s (1.92 rad/s) J4 150 °/s (2.62 rad/s) J5 150 °/s (2.62 rad/s) J6 220 °/s (3.84 rad/s) Robot ...
FANUC R-2000IB/125L.'s 6 AXIS ROBOT WITH R-30iA CONTROLS
Robot Motion Speed J1 110 °/s (1.92 rad/s) J2 110 °/s (1.92 rad/s) J3 110 °/s (1.92 rad/s) J4 170 °/s (2.97 rad/s) J5 170 °/s (2.97 rad/s) J6 260 °/s (4.54 rad/s) Robot Motion Range J1 ±180° J2 +75...
2014 FANUC R2000iB/210F 6 AXIS CNC ROBOT WITH R30iA CONTROLLER
HOURS SHOWN ON METER 16,637 Robot Motion Speed J1 95 °/s (1.66 rad/s) J2 90 °/s (1.57 rad/s) J3 95 °/s (1.66 rad/s) J4 120 °/s (2.09 rad/s) J5 120 °/s (2.09 rad/s) J6 190 °/s (3.32 rad/s) Robot Mot...
2002 UNISON 5000 TRUFLUTE CNC CUTTER GRINDER
Workpiece OD Range 12" Workpiece Length Range 20" Grinding Wheel OD 8" A Axis Unlimited B Axis 180 Degree Total C Axis 20" D Axis 9" Z Axis 10" Grinding Wheel 10 HP 2200-7200 RPM Coolant System Tra...
1993 FADAL 6030 VERTICAL MACHINING CENTER
Table Size 62.5" x 30" Floor to Table Surface 36" T-Slots (No. x Width x Span) 5 x .687" x 5.5" Cutting Feed Rate (X/Y/Z) .01-250 ipm / 375 @ 150% Rapid Travel Rate (X/Y/Z) 400(X/Y/Z) ipm Max. Weig...
NAKAMURA TOME SC250 CNC LATHE W/SUB SPINDLE 2005
Dodecagonal Fanuc 18i-TB Control Sub Spindle Option Bar Feed Interface Weight: 8,377 Pounds | Chuck size: 8" (EQUIPPED COLLET NOSE AND COLLET) | Bar capacity: 2" | Slide travel x axis: 6.988" | Slide travel z...
ACME SINGLE STATION PUSH UP DEBURR MACHINE
MACHINE IS BASICALLY STILL IN NEW CONDITION WITH 426.6 HOURS ON THE UNIT THIS IS A SINGLE STATION PUSH UP BRUSH DEBURR MACHINE. PIECE PART IS LOADED ON WORKSPINDLE WHICH IS POSITIONED VERTICALLY ON...
ACER AGS 1020 AHD HIGH PRECISION HYDRAULIC SURFACE GRINDER
Revolution 0.1" Revolution 0.2" 0.0001" - Per Revolution 0.01" Reinforced high column & heavyweight Meehanite casting. Direct drive spindle equipped with 4 ABEC-7 angular contact ball bearings 10" ...
MITSUI SEIKI 6CM BRIDGE TYPE VERTICAL CNC JIG BORER
= TABLE SIZE 37.75" X 51" BETWEEN UPRIGHTS 44" SPINDLE NOSE TO TABLE MAX. 35" APPROX. SPINDLE SPEEDS 45-2,000 RPM FANUC OM CNC CONTROLS POINTFINDER 2 AXIS DRO'S LARGE ASSORTMENT OF TOOLING